# How to Check Your Stream's Health

> With a business account, the You are Live screen shows how your stream arrives and warns you about missing sound, a frozen picture or a slow upload while you can still fix it. After the event, Event Analytics shows Stream health.

Source: https://www.eventlive.pro/help/how-to-check-your-stream-health  
Section: EventLive Help Center › Using EventLive › Going Live  
Updated: 2026-11-19

When you stream from an encoder, a camera or OBS with a business account, EventLive shows how your stream is arriving and warns you about problems while you can still fix them: no sound, a frozen picture, or an upload too slow for your encoder's settings. After the event, **Event Analytics** shows **Stream health**: how long you were on air, and any drops and their reasons.

## While you're live

1. Start streaming from your encoder, camera or OBS.
2. Open your event in the [Broadcaster Console](https://broadcaster.eventlive.pro/) and choose **How to Go Live**.
3. The **You are Live!** screen shows your stream's health above **Watch Live**. It also appears while you stream a test.

![Stream health on the You are Live screen, with a No sound alert](https://www.eventlive.pro/images/help/how-to-check-your-stream-health/01-live.jpg)

- The first line says **Stream arriving fine**, or names the problem and what to do about it.
- **Upload** is what reaches us now. **Encoder** under it is the bitrate your encoder is set to send.
- **Video** is the resolution, frame rate and codec we receive.
- **Sound** is **On**, **Silent**, or **None** when the stream has no audio track.
- **Speed** says **Real time** while your stream keeps pace. **Falling behind** means the video runs slower than real time, so viewers may see buffering. The alert above it says when your upload is the cause.
- The chart shows your upload over the last 10 minutes. The dashed line is your encoder's setting.
- **Connected via** shows which of our locations your stream connects to.

The card updates every few seconds and runs 10 to 20 seconds behind your stream. In a browser, a problem also puts ⚠ in the tab's title, so you notice it from another tab. The card doesn't show while a pre-recorded video plays.

## Alerts and what to do

| Alert | What it means and what to do |
|---|---|
| **No sound** | Your stream has no audio track. Turn on audio in your encoder or camera. |
| **No sound for …** | The sound is silent. Check that the microphone is on and not muted, and check the encoder's audio input. |
| **Picture frozen** | Check the camera, its cable and the encoder's video source. |
| **Choppy video** | Frames are missing. Lower the bitrate, or close other apps on the streaming computer. |
| **Upload below your encoder's setting** | Less reaches us than your encoder sends. Set the encoder to the bitrate the alert suggests, or use a wired connection. |
| **Upload can't keep up** | Your stream reaches us late, so viewers may see buffering. Lower the bitrate or use a wired connection. |
| **Stream falling behind** | The video runs slower than real time, and the cause isn't clear from what we receive. Viewers may see buffering. If it keeps happening, contact us. |
| **Viewers aren't getting video** or **new video** | If it doesn't recover in a minute, stop your stream and start it again. |
| **Short pause** | We restarted processing your stream. You don't need to do anything. |

**No sound for …** appears after about half a minute of silence. Some encoders keep sending silent audio at full bitrate, which looks like sound to us, so also listen to your stream with **Watch Live**.

When everything is fine, the card may suggest a better setting, such as 4–6 Mbps for 1080p or 2–3 Mbps for 720p. We stream up to 1080p, so sending more uses upload without improving what viewers see. See the [recommended RTMP settings](https://www.eventlive.pro/help/recommended-rtmp-live-streaming-settings).

## After the event: Stream health

Open the event and choose **Event Analytics**. **Stream health** is at the bottom of the page, under the viewer statistics:

- **On air**: how long you streamed, and how much of that time had no issues;
- **Drops**: how many times the stream cut out and came back, and the longest gap. A stop of 5 minutes or more shows as **Paused** instead;
- **Video**: what your encoder sent. **Sound** says **Included** when your stream carried sound; it can't tell whether anyone was speaking;
- a timeline of each broadcast, marked **Good**, **Unstable**, **Problem** and **Off air**, or **No details** where we have no record of a part;
- your **Upload** during the event;
- each drop, pause and problem with its time and reason. **Upload couldn't keep up** means your stream reached us late. **Stream slowed down** means the video ran slower than real time and the cause isn't clear. Slowdowns shorter than a minute are counted on one line.

![Stream health in Event Analytics](https://www.eventlive.pro/images/help/how-to-check-your-stream-health/02-report.jpg)

Times are in the event's time zone, and an event streamed over several days gets a timeline per broadcast. Parts you removed from the replay aren't included. Stream health is for you and your team: it isn't part of **Export PDF**.

Details for the latest part of a stream appear within an hour. Upload and sound details are recorded from November 18, 2026, so older streams show less.
